- 작성시간 : 2016/01/26 09:52
- 퍼머링크 : powerenter.egloos.com/11201983
- 덧글수 : 0
아래 방법은 LVM 묶여있는 경우 소용이 없으며, HW 미러링이 걸려있을 경우 확인할 수 있는 방법을 보여줌
osbackup:/# lvlnboot -v
Boot Definitions for Volume Group /dev/vg00:
Physical Volumes belonging in Root Volume Group:
/dev/disk/disk1_p2 -- Boot Disk ( 해당 부분이 LINE 수가 1개 or 2개 여부로 HW 미러링인지 여부를 확인할 수 있으며, 1개일 경우 HW 미러링으로 보면 됨)
Boot: lvol1 on: /dev/disk/disk1_p2
Root: lvol3 on: /dev/disk/disk1_p2
Swap: lvol2 on: /dev/disk/disk1_p2
Dump: lvol2 on: /dev/disk/disk1_p2, 0
Boot Definitions for Volume Group /dev/vg00:
Physical Volumes belonging in Root Volume Group:
/dev/disk/disk1_p2 -- Boot Disk ( 해당 부분이 LINE 수가 1개 or 2개 여부로 HW 미러링인지 여부를 확인할 수 있으며, 1개일 경우 HW 미러링으로 보면 됨)
Boot: lvol1 on: /dev/disk/disk1_p2
Root: lvol3 on: /dev/disk/disk1_p2
Swap: lvol2 on: /dev/disk/disk1_p2
Dump: lvol2 on: /dev/disk/disk1_p2, 0
1. HP-UX 11.31에서 외부 장치 확인을 하기 위해서는 아래와 같은 명령어를 수행하여, 외부 장치를 검색한다.
backsvr:/]ioscan -fnk | grep -i ext_bus
ext_bus 0 0/0/3/0.0 side CLAIMED INTERFACE IDE Primary Channel (내장형 disk를 표현한 것)
ext_bus 1 0/0/3/0.1 side CLAIMED INTERFACE IDE Secondary Channel
ext_bus 2 0/1/1/0 mpt CLAIMED INTERFACE SCSI Ultra320 A6961-60011
ext_bus 3 0/1/1/1 mpt CLAIMED INTERFACE SCSI Ultra320 A6961-60011 (TAPE 장치를 의히함)
ext_bus 5 0/2/1/0.1.3.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface (HBA 카드와 연결되어 있는 PATH를 의미)
ext_bus 15 0/2/1/0.1.4.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 16 0/2/1/0.1.43.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 9 0/5/1/0.1.5.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 10 0/5/1/0.1.6.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 21 0/5/1/0.1.47.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 14 0/5/1/1.1.0.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 12 0/5/1/1.1.1.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 13 0/5/1/1.1.2.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 17 0/5/1/1.1.42.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 4 255/1/0 usb_ms_scsi CLAIMED INTERFACE USB Mass Storage SCSI
ext_bus 0 0/0/3/0.0 side CLAIMED INTERFACE IDE Primary Channel (내장형 disk를 표현한 것)
ext_bus 1 0/0/3/0.1 side CLAIMED INTERFACE IDE Secondary Channel
ext_bus 2 0/1/1/0 mpt CLAIMED INTERFACE SCSI Ultra320 A6961-60011
ext_bus 3 0/1/1/1 mpt CLAIMED INTERFACE SCSI Ultra320 A6961-60011 (TAPE 장치를 의히함)
ext_bus 5 0/2/1/0.1.3.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface (HBA 카드와 연결되어 있는 PATH를 의미)
ext_bus 15 0/2/1/0.1.4.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 16 0/2/1/0.1.43.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 9 0/5/1/0.1.5.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 10 0/5/1/0.1.6.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 21 0/5/1/0.1.47.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 14 0/5/1/1.1.0.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 12 0/5/1/1.1.1.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 13 0/5/1/1.1.2.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 17 0/5/1/1.1.42.255.0 fcd_vbus CLAIMED INTERFACE FCP Device Interface
ext_bus 4 255/1/0 usb_ms_scsi CLAIMED INTERFACE USB Mass Storage SCSI
2. SAS 컨트롤러에서 RAID 구성 정보등 DISK 구성정보를 확인할때 사용하는 명령어.
newbackup:/# sasmgr get_info -D /dev/sasd1 -q raid
Tue Jan 26 09:31:18 2016
---------- LOGICAL DRIVE 7 ----------
Raid Level : RAID 1 (RAID 구성정보를 확인할 수 있도록 해주는 영역)
Volume sas address : 0x2bed387d25e6cdf
Device Special File : /dev/rdsk/c0t0d0
Raid State : OPTIMAL
Raid Status Flag : ENABLED
Raid Size : 285948
Rebuild Rate : 0.00 %
Rebuild Progress : 100.00 %
Volume sas address : 0x2bed387d25e6cdf
Device Special File : /dev/rdsk/c0t0d0
Raid State : OPTIMAL
Raid Status Flag : ENABLED
Raid Size : 285948
Rebuild Rate : 0.00 %
Rebuild Progress : 100.00 %
Participating Physical Drive(s) :
SAS Address Enc Bay Size(MB) Type State
0x5000c500320612c9 1 7 286102 SECONDARY ONLINE (HW path가 어떻게 설정되어 있는지를 보여주는 영역 , 현 DISK 2개를 하나로 사용 할 수 있도록 raid 구성한 것을 표현함)
0x5000c5003207f7f1 1 8 286102 PRIMARY ONLINE
0x5000c5003207f7f1 1 8 286102 PRIMARY ONLINE
3. SCASI 컨트롤러의 DISK 정보 구성 확인하는 방법 (명령어를 통한)
osbackup:/# sautil /dev/ciss0
******************************************************************************
**** ****
**** S A U T I L S u p p o r t U t i l i t y ****
**** ****
**** for the HP SmartArray RAID Controller Family ****
**** ****
**** version A.02.22 ****
**** ****
**** (C) Copyright 2003-2010 Hewlett-Packard Development Company, L.P. ****
******************************************************************************
**** ****
**** S A U T I L S u p p o r t U t i l i t y ****
**** ****
**** for the HP SmartArray RAID Controller Family ****
**** ****
**** version A.02.22 ****
**** ****
**** (C) Copyright 2003-2010 Hewlett-Packard Development Company, L.P. ****
******************************************************************************
---- DRIVER INFORMATION ------------------------------------------------------
Driver State........................ READY
---- CONTROLLER INFORMATION --------------------------------------------------
Controller Product Number........... P400 ( 컨트롤러 정보)
Controller Product Name............. HP PCIe SmartArray P400
Hardware Path....................... 0/3/0/0/0/0
Serial Number....................... PAFGK0T9SY00WO
Device File......................... /dev/ciss0
Hardware Revision................... 'E'
Boot Block Revision................. 0.04
Firmware Revision (running)......... 7.22
Firmware Revision (in ROM).......... 7.22
Firmware Revision (inactive)........ 7.18
# of Logical Drives................. 2
# of Physical Disks Configured...... 8
# of Physical Disks Detected........ 8
Logical Drive Rebuild Priority...... 0 (low)
Array Capacity Expansion Priority... 0 (low)
Auto-Fail Missing Disks at Boot..... disabled
SCSI Transfer Detection Mode........ Auto Detect
Controller Path Selection Method.... default
Max # of Logical Drives............. 32
Last firmware lockup................ 0
Controller Product Name............. HP PCIe SmartArray P400
Hardware Path....................... 0/3/0/0/0/0
Serial Number....................... PAFGK0T9SY00WO
Device File......................... /dev/ciss0
Hardware Revision................... 'E'
Boot Block Revision................. 0.04
Firmware Revision (running)......... 7.22
Firmware Revision (in ROM).......... 7.22
Firmware Revision (inactive)........ 7.18
# of Logical Drives................. 2
# of Physical Disks Configured...... 8
# of Physical Disks Detected........ 8
Logical Drive Rebuild Priority...... 0 (low)
Array Capacity Expansion Priority... 0 (low)
Auto-Fail Missing Disks at Boot..... disabled
SCSI Transfer Detection Mode........ Auto Detect
Controller Path Selection Method.... default
Max # of Logical Drives............. 32
Last firmware lockup................ 0
---- ARRAY ACCELERATOR (CACHE) INFORMATION -----------------------------------
Array Accelerator Board Present?.... yes
Cache Configuration Status.......... cache enabled
Cache Ratio......................... 25% Read / 75% Write
Total Cache Size (MB)............... 208
Read Cache........................ 052
Write Cache....................... 156
Transfer Buffer................... 000
Battery Pack Count.................. 1 ( DISK 케쉬 베터리가 존재하지 않을 경우 0으로 표기됨)
Battery Status (pack #1)............ ok
Cache Configuration Status.......... cache enabled
Cache Ratio......................... 25% Read / 75% Write
Total Cache Size (MB)............... 208
Read Cache........................ 052
Write Cache....................... 156
Transfer Buffer................... 000
Battery Pack Count.................. 1 ( DISK 케쉬 베터리가 존재하지 않을 경우 0으로 표기됨)
Battery Status (pack #1)............ ok
---- LOGICAL DRIVE SUMMARY ---------------------------------------------------
# RAID Size Status
0 1+0 286070 MB OK
1 ADG 1144281 MB OK
1 ADG 1144281 MB OK
(DISK의 TOTAL 정보를 보여주는 부분)
---- SAS/SATA DEVICE SUMMARY -------------------------------------------------
---- SAS/SATA DEVICE SUMMARY -------------------------------------------------
Location Ct Enc Bay WWID Type Capacity Status
internal 1I 1 8 0x500000e11250b082 DISK 300.0 GB OK
internal 1I 1 7 0x50000393d849af16 DISK 300.0 GB OK
internal 1I 1 6 0x50000393881bd5c6 DISK 300.0 GB OK
internal 1I 1 5 0x500000e1124bd872 DISK 300.0 GB OK
internal 2I 1 4 0x500000e110934132 DISK 300.0 GB OK
internal 2I 1 3 0x500000e1124eb9c2 DISK 300.0 GB OK
internal 2I 1 2 0x5000cca0128ffc41 DISK 300.0 GB OK
internal 2I 1 1 0x500000e1124bd622 DISK 300.0 GB OK
internal 1I 1 7 0x50000393d849af16 DISK 300.0 GB OK
internal 1I 1 6 0x50000393881bd5c6 DISK 300.0 GB OK
internal 1I 1 5 0x500000e1124bd872 DISK 300.0 GB OK
internal 2I 1 4 0x500000e110934132 DISK 300.0 GB OK
internal 2I 1 3 0x500000e1124eb9c2 DISK 300.0 GB OK
internal 2I 1 2 0x5000cca0128ffc41 DISK 300.0 GB OK
internal 2I 1 1 0x500000e1124bd622 DISK 300.0 GB OK
---- SAS/SATA ENCLOSURE SUMMARY ----------------------------------------------
Location Ct Enc Expander_count Bay_count SEP_count
internal 1I 1 0 4 1
internal 2I 1 0 4 1
internal 2I 1 0 4 1
---- LOGICAL DRIVE 0 ---------------------------------------------------------
Logical Drive Device File........... /dev/dsk/c0t0d0
Fault Tolerance Mode................ RAID 1+0 (Disk Mirroring)
Logical Drive Size.................. 286070 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 2
Fault Tolerance Mode................ RAID 1+0 (Disk Mirroring)
Logical Drive Size.................. 286070 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 2
(물리적으로 DISK 2개가 raid 10으로 묶인것을 보여주는 영역)
Participating Physical Disk(s)...... Ct:Enc:Bay:WWID
1I:1:8:0x500000e11250b082
1I:1:7:0x50000393d849af16
1I:1:8:0x500000e11250b082
1I:1:7:0x50000393d849af16
Participating Spare Disk(s)......... Ct:Enc:Bay:WWID
none
none
Stripe Size......................... 128 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0xA013DC34
Media Exchange Detected?............ no
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0xA013DC34
Media Exchange Detected?............ no
---- LOGICAL DRIVE 1 ---------------------------------------------------------
Logical Drive Device File........... /dev/dsk/c0t0d1
Fault Tolerance Mode................ RAID ADG (Advanced Data Guarding)
Logical Drive Size.................. 1144281 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 6
Fault Tolerance Mode................ RAID ADG (Advanced Data Guarding)
Logical Drive Size.................. 1144281 MB
Logical Drive Status................ OK
# of Participating Physical Disks... 6
(나머지 DISK 6개가 DATA 영역으로 묶인 것을 확인)
Participating Physical Disk(s)...... Ct:Enc:Bay:WWID
1I:1:6:0x50000393881bd5c6
1I:1:5:0x500000e1124bd872
2I:1:4:0x500000e110934132
2I:1:3:0x500000e1124eb9c2
2I:1:2:0x5000cca0128ffc41
2I:1:1:0x500000e1124bd622
1I:1:6:0x50000393881bd5c6
1I:1:5:0x500000e1124bd872
2I:1:4:0x500000e110934132
2I:1:3:0x500000e1124eb9c2
2I:1:2:0x5000cca0128ffc41
2I:1:1:0x500000e1124bd622
Participating Spare Disk(s)......... Ct:Enc:Bay:WWID
none
none
Stripe Size......................... 16 KB
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0xA013CF0C
Media Exchange Detected?............ no
Logical Drive Cache Status.......... cache enabled
Configuration Signature............. 0xA013CF0C
Media Exchange Detected?............ no
---- SAS/SATA DEVICE 1I:1:8:0x500000e11250b082 [DISK] ------------------------
Connector Location............................... internal
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 8
WWID............................................. 0x500000e11250b082
Disk WWID........................................ 0x500000e11250b080
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FARTT
Device Serial Number............................. D001P9A03CYU0941
Device Firmware Version.......................... HPD5
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 8
WWID............................................. 0x500000e11250b082
Disk WWID........................................ 0x500000e11250b080
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FARTT
Device Serial Number............................. D001P9A03CYU0941
Device Firmware Version.......................... HPD5
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Disk present and operational................... yes
Non-disk device detected....................... no
S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
---- SAS/SATA DEVICE 1I:1:7:0x50000393d849af16 [DISK] ------------------------
Connector Location............................... internal
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 7
WWID............................................. 0x50000393d849af16
Disk WWID........................................ 0x50000393d849af14
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FBDSP
Device Serial Number............................. EB01PC210WND1208
Device Firmware Version.......................... HPD4
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. REMOVED IN HOT PLUG
Media Type....................................... HDD
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 7
WWID............................................. 0x50000393d849af16
Disk WWID........................................ 0x50000393d849af14
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FBDSP
Device Serial Number............................. EB01PC210WND1208
Device Firmware Version.......................... HPD4
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. REMOVED IN HOT PLUG
Media Type....................................... HDD
Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Disk present and operational................... yes
Non-disk device detected....................... no
S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
---- SAS/SATA DEVICE 1I:1:6:0x50000393881bd5c6 [DISK] ------------------------
Connector Location............................... internal
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 6
WWID............................................. 0x50000393881bd5c6
Disk WWID........................................ 0x50000393881bd5c4
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FBDSP
Device Serial Number............................. ECA1PB909T2U1138
Device Firmware Version.......................... HPD4
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. REMOVED IN HOT PLUG
Media Type....................................... HDD
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 6
WWID............................................. 0x50000393881bd5c6
Disk WWID........................................ 0x50000393881bd5c4
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FBDSP
Device Serial Number............................. ECA1PB909T2U1138
Device Firmware Version.......................... HPD4
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. REMOVED IN HOT PLUG
Media Type....................................... HDD
Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Disk present and operational................... yes
Non-disk device detected....................... no
S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
---- SAS/SATA DEVICE 1I:1:5:0x500000e1124bd872 [DISK] ------------------------
Connector Location............................... internal
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 5
WWID............................................. 0x500000e1124bd872
Disk WWID........................................ 0x500000e1124bd870
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FARTT
Device Serial Number............................. D001P9A03ALV0941
Device Firmware Version.......................... HPD5
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Connector........................................ 1I
Enclosure........................................ 1
Bay.............................................. 5
WWID............................................. 0x500000e1124bd872
Disk WWID........................................ 0x500000e1124bd870
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FARTT
Device Serial Number............................. D001P9A03ALV0941
Device Firmware Version.......................... HPD5
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Disk present and operational................... yes
Non-disk device detected....................... no
S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
---- SAS/SATA DEVICE 2I:1:4:0x500000e110934132 [DISK] ------------------------
Connector Location............................... internal
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 4
WWID............................................. 0x500000e110934132
Disk WWID........................................ 0x500000e110934130
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ DG0300BARTQ
Device Serial Number............................. D002P96051GD0923
Device Firmware Version.......................... HPD0
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 4
WWID............................................. 0x500000e110934132
Disk WWID........................................ 0x500000e110934130
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ DG0300BARTQ
Device Serial Number............................. D002P96051GD0923
Device Firmware Version.......................... HPD0
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Disk present and operational................... yes
Non-disk device detected....................... no
S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
---- SAS/SATA DEVICE 2I:1:3:0x500000e1124eb9c2 [DISK] ------------------------
Connector Location............................... internal
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 3
WWID............................................. 0x500000e1124eb9c2
Disk WWID........................................ 0x500000e1124eb9c0
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FARTT
Device Serial Number............................. D001P9A03C4V0941
Device Firmware Version.......................... HPD5
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 3
WWID............................................. 0x500000e1124eb9c2
Disk WWID........................................ 0x500000e1124eb9c0
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FARTT
Device Serial Number............................. D001P9A03C4V0941
Device Firmware Version.......................... HPD5
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Disk present and operational................... yes
Non-disk device detected....................... no
S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
---- SAS/SATA DEVICE 2I:1:2:0x5000cca0128ffc41 [DISK] ------------------------
Connector Location............................... internal
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 2
WWID............................................. 0x5000cca0128ffc41
Disk WWID........................................ 0x5000cca0128ffc40
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FBDBR
Device Serial Number............................. PMJK5TLB
Device Firmware Version.......................... HPD6
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. MARK BAD FAILED
Media Type....................................... HDD
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 2
WWID............................................. 0x5000cca0128ffc41
Disk WWID........................................ 0x5000cca0128ffc40
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FBDBR
Device Serial Number............................. PMJK5TLB
Device Firmware Version.......................... HPD6
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. MARK BAD FAILED
Media Type....................................... HDD
Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Disk present and operational................... yes
Non-disk device detected....................... no
S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
---- SAS/SATA DEVICE 2I:1:1:0x500000e1124bd622 [DISK] ------------------------
Connector Location............................... internal
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 1
WWID............................................. 0x500000e1124bd622
Disk WWID........................................ 0x500000e1124bd620
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FARTT
Device Serial Number............................. D001P9A03AKU0941
Device Firmware Version.......................... HPD5
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Connector........................................ 2I
Enclosure........................................ 1
Bay.............................................. 1
WWID............................................. 0x500000e1124bd622
Disk WWID........................................ 0x500000e1124bd620
Device Type...................................... DISK
Disk Capacity.................................... 300.0 GB
Device Status.................................... OK
Device Vendor ID................................. HP
Device Product ID................................ EG0300FARTT
Device Serial Number............................. D001P9A03AKU0941
Device Firmware Version.......................... HPD5
Reserved Area (cfg/status info).................. 33554.4 KB (33.6 MB)
Block Size (bytes/sector)........................ 512 bytes
M&P Data Stamped?................................ yes
Last Failure Reason.............................. none
Media Type....................................... HDD
Physical Disk Flags:
Disk present and operational................... yes
Non-disk device detected....................... no
Disk present and operational................... yes
Non-disk device detected....................... no
S.M.A.R.T. supported........................... yes
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
S.M.A.R.T. errors (in factory M&P data)........ no
S.M.A.R.T. enabled............................. yes
S.M.A.R.T. errors (in powerup M&P data)........ no
Attached to external connector................. no
Configured in a logical drive.................. yes
Configured as a spare disk..................... no
Disk write cache enabled at spin up............ no
Supports redundant controller operation........ yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
Disk write cache enabled in current page....... no
Disk write cache disabled in default page...... yes
******************************************************************************
**** End of SAUTIL Output ****
******************************************************************************
osbackup:/#
**** End of SAUTIL Output ****
******************************************************************************
osbackup:/#
덧글